Submissive Male Milking System

BILL OF MATERIALS (BOM)

(THE LIST OF ITEMS NEEDED TO MAKE THIS PRODUCT)

THIS SET IS FOR ONE MALE

SEE OPTION 1 FOR MULTIPLE MALES

AND OPTION 2 FOR A LIST OF POSITIONS THAT
YOU MIGHT TO BUILD SUPPORTS FOR

1 WET / DRY Vacuum cleaner OR plastic pail with lid.

TO HANDLE LIQUIDS

IT MIGHT BE NICE IF THE CONTAINER WAS CLEAR SO PEOPLE CAN SEE IT FILL UP.

BUT THERE ARE REASONS YOU WOULD NOT WANT TO DO THIS:

STDs PRODUCE COLORED OUTPUT

IF SOMEONE WERE TO BLEED

I COULD BE VERY UPSETTING

=====

2 motors BOTH adjustable from VERY slow (10 revolutions per minute (RPM)) OR LESS to VERY fast

GET OVERSIZED (more horsepower AND RPMs than is needed for one person) MOTORS so that when you add more males you are not REQUIRED to change the motors.

You may however want to ADD motors, see option 1 for explanation

=====

2 pump housings

Make sure they can handle wide (deep if you prefer) (from circle nearest nut to circle nearest motor) impellers so it can handle more air when the number of positions go up.

=====

2 Impellers (these move air, like a leaf blower or a vacuum cleaner)

MAKE SURE THEY FIT BOTH THE PUMP HOUSING AND THE MOTOR SHAFT DIAMETERS.

Get the widest / deepest ones possible.

=====

2 Y connectors

=====

6 vacuum hoses OR SOMETHING SIMILAR

=====

2 SETS OF FLEXIBLE (PLASTIC) Tubes / cylinders of different lengths and Diameters (OR PLASTIC ROLLED INTO TUBES).

YOU DO NOT WANT TO CRUSH PENIS OR SCROTUM

BUT YOU DO WANT TO GRAB AND RELEASE THEM AS AIRFLOW CHANGES.

1 SET for the penis

1 SET for the scrotum

=====

2 motor speed controllers

End of basics

=====

OPTION 1 : FOR MULTIPLE MALES

YOU NEED TO ADD

2 MANIFOLD CHAINS

Manifold engineering a chamber or pipe with several openings for receiving or distributing a fluid or gas, such as the intake or exhaust manifolds of an internal-combustion engine

MY DEFINITION

ONE WAY IN SEVERAL WAYS OUT

IT CAN ALSO USED IN REVERSE

SEVERAL WAYS IN ONE WAY OUT

1 CHAIN for the penis(S)

1 CHAIN for the scrotum(S)

=====

AT LEAST 2 more motor speed controllers

MAYBE as many as 6

You give only 1 to a person, as they fight to

Increase / decrease the RPMs they will cause other people to be Stimulated

=====

When using this option you attach hoses 2 and 5 (both of them suck air) To the SINGLE connection on the manifold.

You run the SEVERAL connections ONE per manifold to EACH person.

As in

Manifold 1 (M1) = penis

Manifold 2 (M2)= scrotum

Each manifold has 2 or more positions.

for this example lets say they have 6 positions = (P1, P2, P3, P4, P5, P6)

You run (M1, P1) AND (M2, P1) TO MASTURBATION SUITE 1

EACH MASTURBATION SUITE WILL HAVE MULTIPLE POSITIONS
FROM OPTION 2

YOU MIGHT WANT TO HAVE 2 MOTORS IN EACH SUITE SO EACH PERSON CAN GET THE TYPE AND AMOUNT (PENIS, SCROTUM AN RPM) STIMULATION THAT THEY WANT.

You still attach hose 3 to (M1) inside the suite

=====

OPTION 2 : MASTURBATION POSITIONS

You need to make supports for each masturbation position so that when they go weak from exhaustion they do not hurt themselves.

IT WOULD BE A GOOD IDEA TO STRAP THEM IN POSITION

SO THEY DO NOT BEND THEIR BACK AND HURT THEMSELVES.

YOU MUST HAVE A PERSON IN FOR EVERY 2 SUITES TO MONITOR IN CASE SOMEONE HAS A PROBLEM

YOU DO WANT THE STRAPS A LITTLE LOOSE SO THEY CAN WRIGGLE.

=====

WHEN FACE-DOWN PERSON MAKE SURE THEY CAN BREATH

WHEN FACE-UP MAKE SURE THEY DO NOT CHOKE ON SALIVA

IF YOU CAN COME UP WITH NAMES FOR THE
POSITIONS THAT WOULD BE HELPFUL

POSITION DESCRIPTION

  1. Laying face up on bed spread-eagled
  2. Face down not spread-eagled
  3. Face down on table with hole cut for scrotum AND penis
  4. Face-down on table with hole for penis Penis hose not on, bucket below table Scrotum hose on.
  5. start hands and knees on floor, Chest supported, legs MIGHT be strapped down

YOU GET THE IDEA

=====

DESCRIPTION

IN order not to burn out OR short circuit the motor handling the liquid MOTOR 1 will PUSH AIR OUT.

Attach hose 1 FROM MOTOR 1 “AIR OUT” to one of the TOP ENDS of the Y connector.

Attach hose 2 to the other TOP END this will be attached to the penis

Attach hose 3 to BOTTOM end of Y and to vacuum cleaner (USED AS CONTAINER ONLY or plastic pail.

This hose will handle LIQUIDS

MOTOR 1 PUSHES AIR OUT TO HOSE 1 ATTACHED TO Y CONNECTOR.

THIS CAUSES SUCTION ON HOSE 2 PULLING LIQUIDS FROM BODY.

HOSE 1 THEN PUSHES LIQUIDS INTO HOSE 3

SO THAT THERE IS NO RISK OF MOTOR 2 BURNING OUT FROM LACK OF AIR WE WILL USE THE SECOND Y CONNECTOR AND HOSES 4, 5 AND 6.

Hose 5 is attached to scrotum.

Hose 6 will be DRY

Tubes MUST BE wide enough so that parts can vibrate VERY GENTLY.

You MIGHT wish to put holes in the tubes for better EFFECT

THE TUBES MAY NEED TO BE CHANGED TO A LARGER DIAMETER AS
PENIS AND SCROTUM SWELL.

=====

OPERATION

FIRST

DO NOT CAUSE PAIN

Because it will takes days / weeks to recover.

SECOND

DO NOT CAUSE EXCESSIVE PLEASURE

Because you may not want to have intercourse or anal sex again

Start motors

Attach hoses 2 and 5 to PENIS and SCROTUM

ALTERNATE BETWEEN MOTORS

Adjust motors TO A LOWER RPM as needed so that liquids come out ALMOST continually.

Originally posted 2012-11-15 11:14:20.

Leave a Reply

Your email address will not be published.

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>